Old engines
VAZ 11183 (VAZ 21114)
Lada Kalina cars began to be equipped with VAZ 11183 (or VAZ 21114) power units in 2004, and then it was inherited by the Grant “standard”. This is a rather simple and primitive four-cylinder engine with 8 valves, producing 82 hp. and volume 1.6 l.
It cannot boast of solid power characteristics, but it does not cause any special problems when driving, and it is also very easy to maintain. It is distinguished by its environmental friendliness and reliability, while it also has good elasticity characteristics. In addition, this motor is known as one of the most torquey, especially at the bottom.
An important additional plus is a reliable timing system that prevents collisions between pistons and valves when the timing belt breaks.
But during operation of the motor, some disadvantages may be noted, in particular:
- Possible failure to turn the crankshaft with the starter;
- Strong noise when the starter is operating;
- Even after cranking the crankshaft, the engine may not start;
- There is instability when it is idling;
- The engine does not function at full capacity, which causes a loss of continuity. As a result, there are jerks when the car moves;
- The appearance of shots and claps;
- Increased fuel and oil consumption rates, insufficient oil pressure;
- The appearance of specific high-pitched knocking sounds when the load on the engine increases;
- Overheating of the engine or, conversely, the inability to warm it up to the required temperature for a long time;
- Constant operation of the electric fan, including on a cold engine;
- Reduced coolant level;
- The appearance of extraneous noise or strong vibration of the motor;
- While the engine is running, a signal indicating a malfunction of the power unit control system comes on.
VAZ-21904
VAZ-21904 is a gasoline-powered sixteen-valve turbo engine with a displacement of 1.4 and a power of 163 hp. In addition, it is equipped with a lithium-ion battery and an electric motor. The basis for it was the VAZ-11194 engine; it was installed on Lada Kalina cars in the first generation. As for the VAZ-21904 itself, it is installed on Grant hybrids - VAZ-21904 sedans. The Volzhsky Automobile Plant tested four such vehicles equipped with three different hybrid engine options.
Fifth gear was replaced by the shaft of a robotic gearbox; it rotates thanks to a small electric motor with a power of 11 kW. This option turned out to be simpler and cheaper than using the standard scheme with the electric motor located between the gearbox and the internal combustion engine.
Also, the terms of reference required the developers to fulfill two mandatory conditions - charging a hybrid car from electrical networks used in everyday life and the ability to move it in two modes at once - combined and electric. AvtoVAZ’s partners in the development of electronics were the Russian research institute NAMI and the Ricardo company from the UK. It was NAMI that developed the battery and electric motor for a hybrid car.
The car is capable of starting to move purely on electric power, with the internal combustion engine switched off. During the process of gaining speed, the gear shift will be carried out by a “robot”, and the precise output of the electric motor is responsible for synchronizing the rotation of the gears at this moment. When you start the gasoline engine, the car will begin to work in hybrid mode - with the same gear shifting, in which the electric motor will either help rotate the input shaft of the box, or will switch to generator mode, charging the battery.
According to tests, a hybrid car will consume 21% less fuel than a Granta with a conventional 1.6 engine. (measurements, of course, were carried out in a gentle mode, but the result obtained is very good).
Of course, only a few hope that the hybrid Lada Granta will be in great demand and will be able to generate any significant interest in the car market in the near future. At the moment, such vehicles are nothing more than a kind of aggregate carriers intended for testing various components separately.
If we talk specifically about the hybrid type transmission, its serial production will begin in at least two to three years, and it will be installed on quite expensive Lada cars, most likely C-class. Thus, it is quite possible over time and we should expect an increase in demand for hybrid cars, but the main condition for this is a fundamental change in the attitude towards “ecological” transport not only of motorists, but also of the state, as well as the vehicle manufacturers themselves.
New Lada: Lada Granta we display temperature data on the instrument panel
Engine on Grant: features
So, the Grant 21116 1.6-liter 8-valve gasoline engine is a modernized 1.6-liter VAZ 2114 engine. The idea to modernize the VAZ 2114 engine arose in connection with the release of the Grant car and the transition of the entire model range to Euro-4.
Initially, ICE 21116 was installed on the Lada Priora and then on the Lada Granta and Lada Kalina cars. List of main technical characteristics:
- injection power system;
- in-line 4-cylinder engine with a power of 87 hp;
- engine capacity 1596 cm3;
- the presence of two valves per cylinder;
- the maximum torque is 140 Nm;
- the presence of an intake manifold with extended channels and a flange for an electronic damper (increased torque);
- new H-module.
The 87 hp Grant engine, especially in comparison with its predecessor VAZ 21114, has a lightweight connecting rod and piston group. This feature of the 21116 engine has its advantages and disadvantages.
By lightening the parts and elements of the internal combustion engine, the service life of the valve-piston group decreases, but at the same time the dynamics and other indicators improve. For example, an increase in power to 87 hp, which is 6 hp. more than that of ICE 21114.
Main characteristics of the Lada Grand car with a VAZ 21116 engine installed on it:
- The maximum speed of the car is 167 km/h;
- Fuel consumption 8.5 l. per 100 km (when driving in the urban cycle);
- Fuel consumption 5.7 l. per 100 km (when driving on the highway);
Let's move on. If we consider the Granta 8-valve engine and its design, the Granta 8-valve engine has several design features that distinguish it from other modifications.
Firstly, the plate honing method is used to finalize the surfaces of the cylinders. Secondly, the presence of oil nozzles allows for more intensive lubrication and cooling of the pistons.
The dimensions of the internal combustion engine parts have also been reduced: the height of the cylinder block is about 197.1 mm; the crank radius is about 37.8 mm; piston ring height 1.2/1.5/2 mm, etc.
Another thing worth noting is the electromechanical throttle module installed at the receiver input. This design solution allows the ECU to fully control both the fuel supply and the air supply to the cylinders.
Let us add that the main design feature of the Grant 21116 internal combustion engine was the lightweight ShPG connecting rod and piston group. In the previous model, exhaust gas flows collided and created back pressure.
For this reason, in the case of the VAZ 21116, the designers decided to lengthen the collector pipes by changing the shape of the cylindrical block and the inlet pattern. As a result, such actions helped reduce losses and resistance.
How to find out the body number by VIN code
VINformer only works with 17-digit VINs that comply with the ISO 3779-1983 standard. Enter the VIN in the form on the page and click the Check car button.
The decryption algorithm assumes the possibility of multi-stage decryption (sometimes it may be necessary to select one of several car brands or engine modifications, indicate the sales market, etc.
), but most requests will not require clarification of information, because all parameters are determined automatically.
Please do not try to "punch" body numbers of right-hand drive vehicles produced for the Japanese domestic market, engine numbers, etc.
Any car you see on the street is identified by a unique vehicle identification number (VIN). This number is also quite often called simply the body number.
There are no two cars in the world with the same VIN number. For this reason, the chassis number is sometimes compared to DNA or fingerprints, as it allows the vehicle's identity to be easily and accurately determined.
Where is the body number? detailed instructions
Quite often today you can hear a request to show the VIN code of a car. Advanced drivers are familiar with what this is. Simply put, this is the body number. But let's delve deeper into this concept.
The VIN code of a car is its own identification number assigned to the vehicle at the manufacturing stage. It is usually looked at before buying a car, especially if the car is used.
Particular attention is paid to this particular nuance for the reason that the numbers on the body can often be interrupted. Also, using the VIN code, a vehicle can be checked for theft: just enter the code in a special directory, of which there are now many on the Internet.
New Lada: Replacement of antifreeze Lada Granta 8 valves
Thus, this is a kind of vehicle passport, in the absence of which (for example, as a result of damage in an accident), some difficulties may arise.
It is important to know that the location of the chassis number may vary from vehicle to vehicle. Therefore, if you are wondering where the body number is, then this article is for you.
How to find out the car's equipment
The Autocode service will help you check the equipment of your car for free. The check can be carried out using the VIN code or state registration number. number. Information about the car (body number, state number, VIN) is entered into a field on the website page, after clicking the “Check car” button, data about the car options appears on the screen.
It will take no more than one minute to check the car’s configuration by VIN or state number. By paying for the full report (349 rubles), within 5 minutes you will receive a detailed history of the vehicle’s operation: data on mileage, technical. inspections, compulsory motor liability insurance, number of owners, traffic police restrictions and much more.
The procedure will allow us to draw the following conclusions:
- Compare information about the body number, vehicle documentation provided by the owner of the vehicle with factory information;
- Protect yourself from possible confiscation of the car by the traffic police, if the car is stolen or fines are imposed on it.
Checking by wine or state number will help protect yourself from a bad deal.
Why do you need an engine number?
According to the rules for the development and production of vehicles, the engine must have its own identification number. The engine number on the Lada Granta, as on other cars, is necessary to obtain the following information:
- engine model and its main characteristics;
- manufacturer;
- checking and comparing the data specified in the passport (performed when registering a vehicle, replacing a passport, installing additional equipment, replacing an engine);
- checking the car for the possibility of being stolen (documents may be invalid).
In modern cars, not all units have an identification number. This is due to the fact that quite often the engine is changed to a newer one or with different power ratings. To facilitate the process of replacing the motor from the paperwork side, in many countries the engine markings are not checked and are not indicated in the documents.
Exceptions
Constantly faced with unreadable engine numbers, owners of Lada Granta and other cars find themselves in an unpleasant situation when registering their car. You have to scrub off rust and dirt from the surface of the cylinder block. This takes a long time and creates certain problems.
Recently, Russia adopted a law on changes to the rules when registering a vehicle. Now the documents for the car do not contain the engine number plate and, accordingly, it is not compared with the markings on the unit itself. But in some cases you will still have to find engraving on the part, for example, when installing non-standard equipment (switching to gas) or modifying the engine (increasing power).
On some foreign cars there is no engine code at all. Many vehicle manufacturers have come to this conclusion due to the fact that the engine is increasingly being replaced with a contract one in the event of a serious breakdown. To avoid problems with registering such a car with a donor unit, they stopped indicating this number in the documents and checking it with the engraving on the engine body.
Similar article Engine temperature indicator and sensor on Lada Grant
Lada Granta - which engine is better?
Today I will talk about the engines that are installed on the Lada Granta. Today, only four engines are installed on this car. I will try to briefly talk about the characteristics of each engine, but I will not consider the Granta Sport engine, it is too specific and quite rare.
I’ll start with the most basic one, which is installed on the “Standard” package, this is engine 21186. In fact, this is the same engine that was previously installed on VAZ 21114 cars. The only thing that has changed is that the block has become 2.3 mm higher and the shape of the crankshaft has changed shaft The seats remained the same, that is, 7.12, but the shafts themselves were changed. And in order not to change the compression ratio, the cylinder head was changed. In terms of other characteristics, this is still the same engine from the 14th model. In principle, it has established itself as a reliable unit produced by the Volzhsky plant. One of the disadvantages is the adjustment of the valves (due to the lack of hydraulic compensators), as in any other eight-valve engine from VAZ. Very hard work of the connecting rod and piston group, which produces strong vibration on the body and a characteristic diesel sound. The advantage is the compression ratio of 9.6, which theoretically allows the use of AI-92 gasoline without detonation explosions. Great maintainability - in any garage you can replace almost all units. Well, actually – cheap service.
The next engine is 21116, which was installed on the “Norma” package. The main change is a lighter piston; final honing of the cylinder walls has been applied, which extends the life of the engine and makes it easier to pick up. By changing the piston group, the engine gained 8 N/m. The cylinder head gasket has been changed; now it is metal, two-layer, more durable, similar to that of the Priora. The compression ratio has been increased to 10.5, which no longer allows the use of AI-92 gasoline. Anyone who uses AI-92, know that this cannot be done (more on that later). The engine also received an automatic timing belt tensioner and a toothed belt manufactured with a service life of up to 200 thousand km. and an imported pump with a service life of up to 70 thousand km. In addition, for the first time, graphite linings were used on the cylinder walls of this engine, which increases heat transfer and, accordingly, rapid cooling of the pistons.
The advantages of this unit: low noise, decreased fuel consumption due to lighter pistons, increased power and torque. One of the disadvantages is that if the timing belt breaks, the valve bends. There are no hydraulic compensators, which means adjusting the valves.
The next engine is 21127, which is created on the basis of the 16-valve VAZ-21126 engine, but has significant differences, namely: power increased to 106 l/s, torque to 148 N/m, instead of the mass air flow sensor, DBP and DTV were installed, which eliminated the problem floating speed at idle.
This engine also uses lightweight pistons, a reinforced cylinder block gasket and the compression ratio is increased to 11 units, which means the use of AI-98 gasoline. In addition, this unit is equipped with a hydraulic compensator system, which reduces vibration and eliminates the need for valve adjustment.
This engine combines all the advantages of an 8-valve engine (traction from the bottom) and a 16-valve engine (it picks up well at the top). This is one of the most successful solutions of the Volzhsky plant, a more or less modern engine.
All of the above engines have a knock sensor, which allows you to automatically adjust the ignition timing. But as a negative result: you lose engine power, its efficiency, and reduce its service life. Those. imaginary savings on gasoline can lead to disastrous consequences...
That's all. Let's like and subscribe! )))
What is a car's VIN code and what does it mean?
Each vehicle is assigned a unique identification number (VIN). It is always seventeen digits long and consists of alphabetic and digital characters. Using this unique code you can find out a lot of useful information about the car: production date, place of assembly, brand, manufacturer.
And this is not all the information. For example, by using the VIN code, you can find out whether the car was involved in an accident, whether it caught fire or was not flooded. The ability to correctly decipher the identification number will give you a great advantage when purchasing a car second-hand.
You can prevent yourself from buying a dubious car.
There is no single international standard that defines how the VIN is constructed. Each manufacturer sets the rules for its formation himself. The system is built on such a principle that in no case should the number be repeated - the combination of characters must be unique over the past 30 years.
Each car is assigned only one VIN, and it is the only one and cannot be found on another car. Typically, the VIN code is assigned to a vehicle by the final manufacturer, the one who directly puts the car into operation. The VIN number must be checked for each vehicle.
The entire VIN number is divided into sections. Acceptable characters that can be used in the number are a combination of Arabic numerals from 0 to 9 and letters of the Latin alphabet. The exceptions are the letters I, O, Q.
They are not used to eliminate the possibility of number falsification, because such letters can easily be replaced with others.
It is possible to use separator characters to highlight individual subgroups of a number, to indicate the beginning of the code or its end.
Code Features
The identification number is a unique code containing 17 characters. The code contains data about the manufacturer, year of manufacture of the vehicle, and its characteristics. The number structure complies with ISO-3779-1983, ISO-3780 standards. It is placed in various places, depending on the model of transport. These standards make it possible to connect the international system of identification codes for all vehicles.
The VIN code is indicated in Latin letters and Arabic numerals. The first component allows you to identify the manufacturer of the machine. It contains three designations indicating the code of the country of manufacture and the geographical area. The second component is a description of the identification number, has six characters. They designate the car in accordance with the documents. The third part contains eight letters and numbers. The last four characters of them must be indicated by numbers. The first sign may contain information about the year of manufacture of the car; the remaining signs contain the serial number of the vehicle.
If the manufacturer produces less than 500 cars in one calendar year, the number nine is used for the third digit of the first component of the code.
It is worth noting that the identification number cannot contain the letters of the Latin alphabet I, O, Q, because they are similar to the numbers 0 and 1. You can obtain information about the operation and history of purchase and sale by VIN code not only in the traffic police, but and on specialized websites.
Lada Granta engines 8 valves
This power unit was installed only until December 2014, until it gave way to the 11186 internal combustion engine. This is an injection 8-valve engine with a single camshaft, a timing belt drive and without hydraulic compensators, so the thermal valve clearances here will have to be adjusted yourself. Thanks to special holes in the pistons, if the valve belt breaks, it will never bend.
There are plenty of problems with this engine; first of all, owners are bothered by all sorts of noises, knocks, and vibrations. Unreliable electrics, as well as a capricious thermostat, can throw you many unpleasant surprises. Due to poor fuel, valve burnout sometimes occurs here.
| 1.6 l 11183 MKP5 | |
| Type | injector |
| Fuel | gasoline AI-92 |
| Location | transverse |
| Cylinders | 4 in a row |
| valves | 8 |
| Working volume | 1596 cm³ |
| Power | 82 hp |
| Torque | 132 Nm |
| Acceleration to 100 km/h | 12.6 s |
| Speed (max) | 165 km/h |
| Ecological Class | Euro 4 |
| Consumption city | 9.7 l |
| Flow track | 6.1 l |
| Mixed flow | 7.4 l |
Similarly, the Motor VAZ website talks about all the details of the internal combustion engine design
This unit is an improved version of the previous one. There is already a lightweight piston with anti-friction inserts, a timing belt from Gates with a service life of 180 thousand km, an electronic throttle valve, a developed cooling jacket and many other improvements, thanks to which it was possible to fit this rather old engine into the strict EURO 4 econorms. Due to the new pistons without holes in the bottom, if the valve belt breaks, it almost always bends. Update: in mid-2021, the manufacturer equipped the unit with plugless pistons.
The list of typical malfunctions of this power unit is quite long. Owners of cars with such an engine regularly encounter burnout of valves due to bad gasoline, overheating, oil leaks, failures of various sensors, and also glitches of the E-gas system.
| 1.6 l 11186 manual gearbox5 | 1.6 l 11186 automatic transmission4 | |
| Type | injector | injector |
| Fuel | gasoline AI-92 | gasoline AI-92 |
| Location | transverse | transverse |
| Cylinders | 4 in a row | 4 in a row |
| valves | 8 | 8 |
| Working volume | 1596 cm³ | 1596 cm³ |
| Power | 87 hp | 87 hp |
| Torque | 140 Nm | 140 Nm |
| Acceleration to 100 km/h | 12.2 s | 14.2 s |
| Speed (max) | 167 km/h | 160 km/h |
| Ecological Class | Euro 4 | Euro 4 |
| Consumption city | 9.0 l | 10.4 l |
| Flow track | 5.8 l | 6.1 l |
| Mixed flow | 6.6 l | 7.7 l |
The technical features of the engine are described in an article in Za Rulem magazine
Where is the Engine Number on the Lada Granta ~ TOP-GEER.RU
Where is the identifier and duplicate body quantity of Lada Grant
During registration, the highway patrol inspector checks the number of the body in the documents (PTS vehicle) with the real one, which is duplicated on the body. In addition, when purchasing a car, we recommend checking these numbers and visually inspecting the application site on the body.
Where is the body number?
The body number is located under the hood. Duplicated in two places.
- The number is stamped on the body next to the “glass” on the right side of the car.
Body number on carrier
Body number on the nameplate
the engine number located?
on Grant
.
Engine number LADA Priora/2110/2111/2112/Granta/2113/2114/2115/Kalina
The engine number is located
on the engine block under the thermostat above the box. Very often it rusts too.
Once you've climbed the trunk, we recommend installing a net in it, as well as how to choose a net in your trunk here.
When I recorded the entry, I looked for the body number in the usual place for AvtoVAZ. This place. a niche for the luggage compartment for reserve, it was here on all my previous Lada models (VAZ-2109, VAZ-2114, VAZ-2115, LADA PRIORA).
There is no body in the luggage compartment niche in the Lada Grant car!
Is there a body number in the cab
Before I go and put the car on the record, I read online that there is a duplicate number in the back seat in the middle. It was also written that you need to lower the backrest, remove the upholstery from the seal, or find a slot in the upholstery under which the number will be placed.
This information is incorrect, and the standard Lada Granta car does not have a body number in these places!
Under the upholstery
Where does the body inspector look at the traffic police when registering?
The DPS inspector, when recording license plate checks only in the engine compartment, we recommend that they carefully wipe down before the inspection procedure. top-geer.ru
top-geer.ru
Where is the engine identification number on the Grant?
When it becomes necessary to check the license plate of a power unit, the driver faces a difficult task. To understand where the engine number is on a Grant, you need to at least have an idea of the appearance of automotive mechanisms.
Under the hood of the Lada Granta there is not only an engine, but also other important units and devices. The engine itself is located in the middle of the engine compartment, but you can see the designation plate only after performing several actions:
- Open the hood of the Lada Granta, first prepare a flashlight, rags and a set of screwdrivers.
- Remove the air filter.
- After removing it, access to the end of the cylinder block will open. It is engraved with numbers. As a rule, this surface is covered with dirt, machine oil and other contaminants. You need to clean the surface with a cloth and soapy water.
- If exposed to moisture, the applied markings could become rusty and difficult to read. To remove rust, use a special product such as WD-40.
- After all cleaning procedures, the number should become visible. If it is inconvenient to read, you can use a mirror to reflect it at a certain angle.
Similar article What kind of oil to pour into an 8 valve Lada Granta
Engine number on 16 valve
The Lada Granta is available with two types of engines: 8 and 16 valves. The design of the units does not have any major differences. A larger number of valves ensures engine acceleration and better technical characteristics.
On the more powerful Lada Granta, the engine number is also located on the end of the cylinder block on the right side, if you stand in front of the hood. The location of the engine itself in the engine compartment is no different for both versions.
Engine number on 8 mi valve
The very first Grants, produced since 2011, were equipped with 8 valve engines. It is this fact that may explain that the engine designation on early production cars may be in a more deplorable state.
Over 8-9 years of operation, the place on the cylinder block where the marking is applied is often subject to rust and covered with a layer of dirt. To make the engine symbol visible and legible, effort must be made to clean the surface.
List of places to indicate the engine number for a number of popular car brands
| auto | Number indicator location | scheme |
| Audi cars | ||
| A3 | 2006-08 years of production On the left edge, in the place where the engine and gearbox connect Additionally, a plate with a number indicator on the surface of the motor housing | |
| A4 | 2001 release. On the left edge, on the motor housing There is also a plate with a number index on the casing | |
| A6 | 2001-04 years of production. On the left edge, on the motor housing. There is also a plate with a number index on the casing 2005-08 years of production. From the facade, on the motor housing. To see, you need to lift the cover. Also on the cooling system pipe. | |
| Q7 | 3.0 TDI, 2007-08 model year. On the left front side, above the timing belt of the high pressure fuel pump | |
| BMW cars | ||
| Episode 1 | On the right side of the motor housing | |
| Chevrolet cars | ||
| Aveo | On the right side of the oil level control tube | |
| Lacetti | At the bottom of the intake manifold on the engine housing | |
| Lanos | On the right side of the oil level control tube | |
| Citroen cars | ||
| C4 | 1.6 liters - at the place where the engine connects to the gearbox, namely on the right side of the oil level control tube 2.0 liters – On the left side of the oil level control tube | |
| Ford cars | ||
| Focus | There is a special space left for the number where the engine connects to the gearbox. | |
| Mondeo | From the rear driver's side | |
| Transit | From the front right side below the generator 2.5D 4HB: On the left side of the engine, next to the pad on the block Dura Torq 2.5D: on the right side on the head of the engine housing on top of the intake manifold In addition, from the rear right side above the crankcase flange | |
| Honda cars | ||
| CR-V | At the bottom of the manifold where the engine connects to the gearbox | |
| Hyundai cars | ||
| Solaris | In front, on the engine housing at the bottom of the antifreeze filler neck | |
| Santa Fe | Where does the engine connect to the gearbox? | |
| Kia cars | ||
| Rio | On the front of the engine housing at the bottom of the antifreeze filler neck | |
| Spectra | At the bottom of the motor housing cover in a special place behind the motor | |
| Mitsubishi cars | ||
| Pajero | Near the fuel filter. Or in the place where the engine is connected to the gearbox (depending on the specific model) | |
| Nissan cars | ||
| Qashqai | From the front left side of the motor housing | |
| Primera | From the front of the engine at the bottom of the oil level control tube | |
| Opel cars | ||
| Aster | On the left side of the engine crankcase | |
| Corsa | On the right side of the engine, at the bottom of the oil filter | |
| Renault cars | ||
| Logan | On the rear left side of the engine housing near the oil sensor | |
| Megan | At the bottom of the motor, at the top of the motor protection on the radiator side. It can be seen both above and below | |
| Sandero | On the rear left side of the engine housing near the oil sensor | |
| Skoda cars | ||
| Fabia | 1.2 l., 2004-2008 production On the engine housing, in front of the gearbox | |
| Octavia | To the left of the engine near the battery | |
| Toyota cars | ||
| Avensis | In the first picture for motors 1AZ-FE, 1AZ-FSE, 2AZ-FSE In the second picture for motors 3ZZ-FE, 1ZZ-FE | |
| Land Cruiser cars | ||
| Prado | In the wheel arch. The steering wheel must be turned all the way. In the wheel arch on the right, you need to remove the curtain; it is secured with special clips. | |
| Volkswagen cars | ||
| Golf | 2005-2009 years of production On the left side, in the place where the engine connects to the gearbox. In addition, there is a plate with a number index on the surface of the head cover of the motor housing | |
| Jetta | 2005-2008 years of production. On the left side, at the place where the engine connects to the gearbox. In addition, there is a plate with a number index on the surface of the head cover of the motor housing | |
| Passat | 2000-2005 years of production. On the left side, on the motor housing There is also a number plate on the lid 2006-2008 years of production. On the left side, at the place where the engine connects to the gearbox. In addition, there is a number plate on the head cover of the motor housing. | |
| Tuareg | 3.2 liters, 2003-2007 years of production: On the motor housing near the vibration damper 2.5 TDI, model years 2003-2009. At the place where the engine connects to the gearbox 3.0 TDI, model years 2006-2010. From the front left side at the top of the high pressure fuel pump timing belt. | |
| VAZ 2107 | On the cylinder module, at the top of the oil filter | |
| VAZ 2114 | On the cylinder module at the top of the thermostat |
Registration — Lada Granta, 1.6 l., 2014 on DRIVE2
I didn’t see much sense in the writing about registration, if not for one BUT.
I thought that I would register without B, as was the case with four, but I was a little mistaken. I, like smart Masha, am registered on the government services website. So I followed the same path, signing up for registration in the morning. I made an appointment at 9:30, believing that an hour from 8:30 would be enough for me to complete the inspection report. I was thinking, well, what is there to look at in a 14-year-old car... That’s my main mistake =) When checking the engine numbers, I was confronted with the fact that they couldn’t distinguish the number (despite the fact that it wasn’t the nasty “Arkasha”, who came across me at four, and a normal guy - he re-examined the Streetking Passat when he was also forced to clean the engine number, he also inspected my girlfriend’s Corsa and then everything was no problem with him). So I drove to the parking lot, thinking about how, where and with what I would rub the license plate. I knew its location, because... the day before, just in case, I looked for this information on Google. There is nothing to rub. I went to the store to buy napkins. In a good way, you need to remove the air vent and it seems like the number will be visible. It is easy to remove the filter housing without tools, but the problem was that the tube from the expansion tank (4) and the terminal from the battery (5) did not want to snap off, and they were attached to the filter housing with a clip-clamp.
2-engine number. junction between box and engine
But I don’t have screwdrivers, like 80% of the visitors that day did. This is understandable, no one has a new car or tools. So I started to rub the number like this, without removing it. I rubbed it for half an hour, lowered my phone 50 times and took pictures of that place, but what I saw there was a rusty area. I have attached the best photos of the process) these are several photos in which I was on the computer at least a little, but I saw the engine number
Full size
once
Full size
and two
After half an hour of trying to scrub off the rust, I was lucky and a guy nearby had a set of screwdrivers, which I used to remove the clamps from the air. I was very surprised that the number was barely visible on this site.
I passed the act, but missed the line at the window by an hour. I took a ticket to the general queue at 10-30, and at 13-30 I registered. It’s good that you were smart enough not to sit there all this time.
Full size
the final
The moral of this story is that you should rub your number at home)
How to find out which engine is on the grant
Hello, I became the owner of a Lada Grant and in this honor I signed up for your community. I switched from eight.
And I immediately have a question: how can you accurately determine the engine model? I have an eight-valve engine, the passport says 87 hp. like 11186 with lightweight pistons (which bends the valve in the event of a toothed belt break), but the old-style plastic timing belt casing, like on the 11183 engine (which does not bend the valve). As a result, I am in a stupor, and on the block I only found the inscription 1118... and how can I find out what kind of heart is beating under my hood?
Engine
The larger the engine capacity, the more powerful the car, and, as a rule, the larger it is. There is no point in installing a small-capacity engine on a large car, the engine simply cannot cope with its weight, and the opposite is also pointless - installing a large engine in a light car. Therefore, manufacturers are trying to select a motor. to the price of the car. The more expensive and prestigious the model, the larger the engine capacity and the more powerful it is. Budget versions rarely boast a cubic capacity of more than two liters.
Engine displacement is expressed in cubic centimeters or liters. Whichever is more convenient for you.
The engine capacity of the Lada Grant is 1.6 liters.
Lada Granta engine power ranges from 82 to 106 hp.
Despite belonging to the budget price group, the Lada Granta is equipped with several power plants. Each motor has its own characteristics in terms of consumption, maximum speed, power and other parameters, so that each buyer can easily make a choice in full accordance with his own needs. Engine malfunctions and service life indicators are also different. They also need to be taken into account when choosing.
Decoding the number on Grant
The engine number on the Lada Grant occupies a small area on the left side of the engine cylinder block along the direction of the car. It consists of two numbers: a five-digit designation of the engine model (for example, 21126), and a seven-digit unique code of the unit itself (absolutely any numbers).
The first 5 digits correspond to a specific model of internal combustion engine installed on the Lada Granta. At the moment, there are four modifications of engines for this vehicle.
| Engine designation | Power, hp | Number of valves |
| 11183 | 82 | 8 |
| 11186 (21116) | 87 | 8 |
| 21126 | 98 | 16 |
| 21127 | 106 | 16 |
Using the second number, you can determine where the motor was made (factory code) and the year of manufacture by picking up documents at the manufacturer. Any complex mechanism or device produced in production has its own unique code. It is indicated in the accompanying documents and can be used to track the entire path from the start of assembly to its installation on a specific vehicle.
Vehicle registration details
The rating data is given on the plate attached to the upper cross member of the radiator frame on the right side. The Vehicle Identification Number (VIN) is stamped on the right mudguard cup, near the shock absorber upper mount mount.
Vehicle registration details in the engine compartment
: 1 – vehicle identification number (VIN);
2 – vehicle data plate. The identification number is deciphered as follows: XTA
- according to international standards, indicates the manufacturer’s code;
219000
– car model;
C
(letter of the Latin alphabet or number) – model year of the car;
0000000
– body number.
Decoding the sign
:
“AVTOVAZ”
is the designation of the manufacturer.
No. E – RU.MT02.В.00232
– vehicle type approval number;
XTA219000 C 0000000
– vehicle VIN;
1560
– permissible gross vehicle weight, kg;
2460
– permissible weight of a vehicle with a trailer equipped with brakes, kg;
1–810
– maximum permissible load on the front axle, kg;
2–850
maximum permissible load on the rear axle, kg;
vertical inscription on the left No. for spare parts
– indicates the number for spare parts;
The vertical inscription on the right indicates the engine model.
The engine model and number are stamped on the cylinder block area located above the clutch housing under the thermostat (you can see the number by removing the air filter housing or using a small mirror).
Identification numbers of Lada Granta.
Location of identification numbers in the engine compartment.
1 — vehicle identification number;
2 — engine number (on the top of the cylinder block, above the clutch housing);
3 - summary plate with vehicle nameplate data.
According to existing legislation, each vehicle has an identification number (VlN code). This number is recorded in the vehicle passport (PTS). The identification number and other passport data of the vehicle are indicated in the summary plate.
The identification number is stamped in the engine compartment on the amplifier (support cup) of the right mudguard.
An identification number.
Summary plate.
1 — number for spare parts (corresponds to the serial number of the car that came off the assembly line);
2 — vehicle type approval number;
3 — identification number (XTA—manufacturer’s code; 219000—car model; C—year of manufacture; last seven digits—body number);
4 — engine model;
5 - maximum permissible vehicle weight;
6 - maximum permissible weight of a vehicle with a trailer;
7 - maximum permissible load on the front axle;
8 — maximum permissible load on the rear axle;
9 - codes for vehicle version and equipment.
| 2011 | B |
| 2012 | C |
| 2013 | D |
| 2014 | E |
| 2015 | F |
| 2016 | G |
| 2017 | H |
| 2018 | J |
| 2019 | K |
Note. The model year of production of VAZ cars begins on October 1, three months earlier than the calendar year.
The engine model and serial number are stamped on the left end of the cylinder block above the clutch housing.
Hello. Can you tell me where the engine number is located? I register the car.
- Extraneous noise started in the engine area of a VAZ Granta - 7 answers
- Howl in the VAZ Granta engine - 5 answers
- The oil pressure light in the Grant is on at idle - 3 answers
- How much horsepower is the Lada Granta? – 2 answers
- The spark plug in the VAZ Granta is dirty - 2 answers
Remove the air filter box, then you can see the engine number (or look through the mirror). But in general, the engine has long been transferred to the category of consumables, and its number is not checked when checking the numbers in the MREO. And in the vehicle registration certificate, there is now no line about the engine number.
The model and engine number on the Lada Granta are stamped on the end of the cylinder block above the clutch housing. You can read the number using a mirror.
“>
Engine compartment of Lada Granta (VIN number)
This article provides information about the components located in the engine compartment of the Lada Granta car. A decoding of the designation on the nameplate (VIN number) is also given. The location of the VIN marking on the support cup and the place where the engine number and its model designation are stamped are shown.
Fig. 1 View of the engine compartment with a VAZ 21116 (VAZ-11186) engine 1.8 - strut supports, 2 - intake manifold; 3 — throttle assembly; 4 — air-conducting rubber sleeve; 5 — brake fluid reservoir; 6 - battery, 7 - minus marks; 9 — expansion tank; 10 — power fuse block; 11- air filter housing; 12 — air flow sensor; 13 — thermostat; 14 — ignition coil; 15 — side of the oil filler neck; 16 — oil level dipstick; 17- generator; 18 — cover of the gas distribution mechanism drive.
Fig.2 View of the Lada Granta nameplate from the engine compartment. 1 - manufacturer; 2 — number for ordering spare parts; 3 - maximum permitted weight of Lada Granta; 4 — load on the rear axle of the car; 5 - car version; 6 — engine model; 7 — vehicle approval mark; 8 — VIN number; 9 - permissible weight of the vehicle with trailer; 10 — load on the front axle of the car; 11 — configuration number
Fig.3 Identification number stamped on the right support of the car
Fig. 4 Location of passport information about the car. A- VIN; B - identification plate; B - engine model and number (marking is marked on the power unit, more details in Fig. 5)
Fig.5 Place of marking of engine number and model. (air filter housing removed)
In order to comfortably read the markings, it is better to use a mirror.
VIN code
1. The identification number (VIN) is stamped on the floor under the front passenger seat on the right side. To inspect the room, a valve has been cut out of the carpet. The VIN code is also duplicated on the wall between the engine compartment and the engine.
Depending on the configuration of the Lada XRAY, there may be a glove box under the passenger seat. In this case, to access the number, you must fully extend the movable part of the glove box by pulling the stops outward on both sides.
2. The marking (nameplate) is located on the right pillar, below, near the threshold.
It indicates the model, car number, engine model, weight data, number for spare parts, design options, and configurations. Explanation:
- Manufacturer's name OJSC AVTOVAZ (AVTOVAZ).
- Vehicle type approval number. It is given in full in the vehicle passport.
- Vehicle identification number VIN.
- Technically permissible maximum vehicle weight.
- Technically permissible maximum weight of a road train.
- Technically permissible maximum axle weight on the front axle.
- Technically permissible maximum axle weight on the rear axle.
- Vehicle designation.
- Engine designation.
- Number for spare parts. The number for spare parts corresponds to the serial number of the vehicle leaving the assembly line. When ordering spare parts, you must refer to the information contained on the identification plate.
- Market circulation sign.
Let us recall that in accordance with the Decision of the Customs Union Commission dated June 15, 2011 No. 711, the model year is defined as a conditional year indicated by the manufacturer (usually following the actual year of manufacture of the vehicle).
At JSC AVTOVAZ, the start of the model year is set on July 1 of the calendar year. Thus, from January 1 to June 30, the model year corresponds to the actual year of manufacture of the car, and from July 1 to December 31 corresponds to the one following the actual year of manufacture of the car.
1-3 characters - Manufacturer's identification code
4-5 characters - model code
6th sign - body type
7th sign - engine
8th character - gearbox type
- 1- manual transmission VAZ
- 2- AMT
- 3-speed manual Renault
- 4 — JATCO variator
9th character - always 0
10th character - model year
11th character - factory code
12-17 characters - serial number
In some vehicles, the unit number is duplicated in the trunk and interior. This does not apply to Lada Granta. In this vehicle it is indicated only in the engine compartment.
Location of the Lada Granta engine number in the engine compartment:
- Vehicle identification number;
- Motor number (located on the corner of the block, above the body part);
- A table indicating the vehicle's passport data.
In order to find the engine number for the Lada Granta, you need to open the hood and carefully inspect the parts. The desired object is located at the end of the cylinder block above the clutch housing. Sometimes some parts may interfere with normal inspection of the surface. In such cases, use a mirror and a flashlight. If you do not have such a device, you can remove the air filter, which will give you an overview of the desired area. When going to the traffic police, it is not recommended to remove spare parts, since they have their own way of inspecting the engine compartment.
Often, car owners cannot find the code for an 8-valve VAZ engine due to rust or dirt mixed with the engine oil. In such cases, first of all you need to clean the surface to be inspected. To do this, you will need a rust removing solution, a wire brush and a clean rag. After cleaning, it will be easier to view the surface.
What to do if the number is interrupted
If the engine number on the Lada Grant looks like it has been changed, do not rush to conclusions. Perhaps the marking area is covered with rust, and you need to try to scrub it off first. If, after all attempts, the motor code does not correspond to the actual one and mechanical damage is visible, you should contact a specialist.
Similar article Technical characteristics and operation of the 1UZ FE engine
Forensic examination deals with such issues. It gives a conclusion about whether the number is really interrupted, and whether there is information in the database about the criminal history of this car or engine. If the car was purchased at a dealership, then all claims must be presented in an official form to the owners of the organization. In case of a voluntary resolution of the conflict, the salon administration must return the money.
Things are more complicated if the Lada Granta was bought secondhand from a stranger. You can try to find out from the seller whether he knew about the discrepancy between the numbers on the engine. If you cannot return the car to the previous owner, you need to solve this problem yourself. For example, replace the engine with a contract one with a different number.
What is a VIN code?
The ISO 3779 standard, which describes the format of the vehicle VIN code (which translates as Vehicle Identification Number), was adopted in the USA and Canada in 1977. The adoption of this standard has made it possible to create a simple and reliable way to classify machines and protect them from theft. The combination of numbers and letters of the VIN code is protected from number alteration by using an algorithm for calculating the check number, which is followed by all car manufacturers in the USA and exporters to this country; in Europe, the ISO 3779 standard is not always followed. According to the ISO 3779 standard, the VIN code is SEVENTEEN characters long. The following symbols are allowed to indicate the VIN code: 0 1 2 3 4 5 6 7 8 9 ABCDEFGHJKLMNPRSTUVWX YZ The symbols I, O, Q are prohibited due to the similarity to 0 and 1 and to each other.
