Review of the Starline A62 alarm system with detailed instructions

Author: Victor

The Starline A62 car alarm is an anti-theft telematics complex that provides for the use of four security zones. The system protects the car engine with a blocking relay, the doors with limit switches, the body with an impact controller, and the ignition with a special control input.

[Hide]

Specifications

Description of the main characteristics of the Starline A62 Dialog Can Flex:

1. The transmission of commands between the microprocessor and the transceiver is carried out over a radio channel with a frequency of 433 MHz.
2. This model of security complex is controlled by using 128 channels.
3. The maximum range of the key fob in message transmission mode varies around 800 meters. When receiving signals from the transceiver, this figure increases to 2000 m.
4. The range of the spare pager is 15 m.
5. The sensor for recording impacts and physical impacts on the body belongs to the class of piezoelectric devices.
6. The temperature range for efficient operation of the microprocessor is from -40 to +85 degrees.
7. The security system is powered from a 12-volt power supply. Voltage surges in the range from 9 to 18 V are allowed. However, the installation of the Starline A62 anti-theft system cannot be carried out on motorcycles or heavy-duty vehicles.
8. Protection of power lines of the security complex is carried out using safety devices. The rating of the element depends on the specific electrical circuit.
9. When operating in vehicle security mode, the system will consume no more than 25 mA of current.
10. To power the main key fob, equipped with a screen, AAA batteries are used, each of which is rated at 1.5 V. The spare communicator uses CR2450 class elements of 3 volts.

The Starline A62 alarm system uses the “Fast Dialogue” technology with a crypto-resistant dialogue code and a personal encryption key. Thanks to this, the likelihood of electronic hacking of the system is minimized.

Features of the StarLine A62 Dialog car alarm:

Benefits for installers:

• The function programming algorithm has been modernized. Now online on the key fob display you can see the function number and its programmed value.
• The control of additional channels has been modernized, making it possible to install the StarLine A62 Dialog system on all modern cars.
• StarLine A62 Dialog models can be easily transformed into a security and search complex by adding one of the StarLine GSM/GPS modules, which will connect to the alarm system via a local network via one single 3-pin connector.
• To increase anti-theft security, StarLine R2 digital wireless locking relays can be connected.
• More than 50 standard and programmable functions provide the car owner with not only reliable protection, but also comfort when using the StarLine A62 Dialog car alarm.

Equipment:

• central alarm unit
• 1 key fob with two-way communication with LCD
• 1 key fob with two-way communication without LCD
• 2-level shock sensor
• transceiver
• hood button
• Light-emitting diode
• service button
• set of wires
• engine temperature sensor
• installation instructions
• user manual
• User's memo

StarLine A92 Dialog CAN systems are compatible with more than 150 car models.

More than 50 standard and programmable functions provide the car owner with not only reliable protection, but also comfort when using the StarLine B92 Dialog CAN car alarm.

Equipment

Overview of the elements included in the delivery set of the Starline A62 car alarm for cars:

1. Service documentation for installation, connection and configuration of the security system. The manual includes an electrical diagram that will allow you to connect all components of the anti-theft system.
2. User's note.
3. Guarantee document.
4. Main pager for system management. The device is equipped with a screen, thanks to which it has a two-way communication function. Information about the operation of the car alarm is displayed on the display in the form of indicators.
5. Microprocessor module for system control. The device is housed in a rectangular plastic case.
6. Transceiver with built-in antenna module. Equipped with a wire and connector for connection.
7. Additional keychain. The pager is not equipped with a screen, so it does not provide feedback.
8. Shock and sensitivity sensor of two-level type. Equipped with a wire and a connection block.
9. Battery for use in the main pager.
10. Limit switch for installation on the hood.
11. Button to enter the service mode for servicing car alarms.
12. LED system status lamp.
13. Wire for connecting a digital CAN interface.
14. A set of wires and connectors for connecting to the on-board network.

The Starline A62 car alarm package does not include limit switches for installation on doors and a siren; these devices are purchased additionally.

Car alarm delivery set

1. Installation instructions.
2. User manual.
3. Warranty card.
4. User note.
5. Basic key fob with remote control system and LCD display.
6. Central processing unit.
7. Modular transceiver with built-in antenna.
8. Spare control key fob.
9. Shock sensor with two levels.
10. Battery.
11. Hood end switch.
12. Transceiver cable.
13. Service button.
14. Cable for shock sensor.
15. Indicator with built-in diode.
16. Cable for connecting the CAN bus.
17. Main 14-pin connector cable.
18. Cords for connecting limit switches.
19. Cable for central locking.
20. Wires for the contact of the built-in interlock.

Basic alarm functions

Options that are implemented in the Starline A62 Dialogue system:

1. Controlling the security mode using a key fob or a button to enter the service mode. In the second case, the user's personal password is used.
2. The presence of passive blocking of the machine engine.
3. Anti-robbery option. This function is intelligent and is used to block the motor in the event of a forceful seizure of the vehicle. After the attack, the user can enable the option, which is activated after 30-60 seconds. This is done for the safety of the car owner, so that the attacker drives away from him, but does not go far from the crime scene.
4. Self-diagnosis when protective mode is turned off. The alarm system tests its main elements and identifies failed equipment. Information about this is displayed on the communicator screen.
5. Possibility of separate opening of door locks.
6. Bypassing the non-working protection zone. If defective security zones were detected during the check, the system will bypass them.
7. The presence of a memory module built into the microprocessor. The control unit stores data about alarm events indicating the zones that led to their activation. The memory module also stores information about the system state. If the power is turned off, when it is turned on again, the alarm will return to its original state.
8. Preservation of the power unit locking in case of dismantling the alarm system.
9. Possibility of installing and connecting additional shock and sensitivity sensors.
10. Silent security function. When the alarm mode is activated, the siren does not sound. Information about this is sent only to the communicator with a display.
11. Panic mode. Its essence is to activate alarms and lights upon command from a pager. This will scare away potential intruders from the car and designate the vehicle as protected.
12. Calling the car owner. The implementation of the option was made possible thanks to the presence of a button on the transceiver module.
13. Control of door locks from the ignition system.
14. Monitoring the battery charge in the pager. Information about the operation of the battery is displayed on the key fob display.

Video: functional features of the Starline A62 car alarm

User Yaroslav540 presented a detailed overview of the functions and characteristics of the Starline A62 anti-theft system.

Functions

Functions of the A62 security complex:

• car security with alarm signals, siren and lighting;
• forwarding a notification to a remote control with a 2-way communication channel;
• possibility of protection without sound signals;
• automatic activation of protection when the button is accidentally pressed;
• control of protective modes without using a key fob is provided;
• support for additional immobilizer mode;
• non-volatile memory unit that retains its state when the battery is disconnected;
• built-in diagnostic module that automatically excludes faulty zones from protection;
• possibility of 2-stage protection disabling;
• support for calling from the car.

Advantages and disadvantages

Advantages of the A62 security complex noted by the owners:

• price;
• a key fob with a display is provided;
• simple installation and configuration algorithm;
• large radius of command transmission;
• The use of expansion modules is allowed (for automatic motor start).

Equipment disadvantages:

• There have been cases of decrease in the range of the remote control during operation;
• GSM block is not provided;
• no automatic start;
• The equipment has been discontinued, which causes problems in finding original components.

Advantages and disadvantages

Overview of the advantages that Starline A62 alarms have:

1. Protection of all system elements from signal interception and hacking.
2. The strength of the pager, as well as its ergonomics. The key fob is equipped with a shock-resistant case, which eliminates the possibility of its breakage as a result of a fall or other mechanical damage.
3. The presence of a Russified key fob interface simplifies the process of setting up functions. In addition, the communicator has a backlight, so the user can conveniently change system parameters in the dark.
4. Affordable price with extensive functionality and reliable operation of the system.

As reviews from car owners about the Starline A62 alarm system show, this model has no serious shortcomings.

Typical malfunctions of car alarms

Starline A62

The sensor must be firmly attached to the body, placing it approximately in the center.

Starline A64

Starline A66

Installation instructions

Installation manual for Starline A62:

1. The ignition and all electrical devices in the car are turned off. It is necessary to de-energize the on-board network; to do this, disconnect the terminal with the negative contact from the battery.
2. A microprocessor is installed inside the vehicle. To install the unit, you should choose a place that is maximally protected from external influences, moisture and elevated temperatures. The module is installed on a flat surface, preferably behind the instrument panel, this will ensure a minimum length of wires for connection. Plastic clamps or self-tapping screws are used for fixation. To protect the microprocessor module from moisture and vibration during driving, the device can be additionally wrapped in cellophane and foam rubber.
3. A siren is installed under the hood of the car if one is to be used. The use of this device is not necessary, since alarm signals can be organized using the steering horn. If an autonomous siren is used, then during installation it is necessary to ensure free access to the keyhole installed in it.
4. A transceiver with a built-in antenna is placed on the car window. The glass surface is first cleaned and degreased, which will ensure high-quality contact. There should be no electronic devices or metal parts of the body within 5 cm of the transceiver. Their presence will cause interference and reduce the range of the key fob.
5. The shock and sensitivity sensor is installed in the car interior, preferably in the central part of the body. For installation, you can choose a metal partition separating the engine compartment. The device is fixed on a flat surface using plastic clamps, screws or glue. The use of plastic or rubber gaskets is not allowed; this will lead to incorrect operation of the sensor and its premature operation.
6. Limit switches are installed on the hood, trunk and doors. Installation of devices is not permitted in drains. The wiring from the sensors is routed to the microprocessor module.
7. The button to enter the service mode is located inside the car. It is recommended to hide it, but in such a way that the consumer has access to the device from the driver’s seat.

Video: installation of StarLine2011 on Peugeot 308

The StarLine2011 channel in its video showed in detail the process of installing the Starline A62 alarm using the example of a Peugeot 308 car.

Technical capabilities of car alarms A62, A64 and A66

The main functions that these security systems provide:

• data transmission at a frequency of 433.05 - 434.70 MHz over 128 radio channels;
• the range of the main key fob is 800 m in control mode and up to 2000 m in pager mode;
• the radius of the additional remote control without a monitor is 150 m;
• engine blocking using a relay;
• controlled channels for connecting various additional functions;
• “Anti-robbery” and “Panic” modes;
• silent car protection;
• the ability to connect autostart and control from a mobile phone when installing the StarLine M21 module;
• protection against radio interference in large crowds of cars;
• low power consumption (no more than 25 mA in security mode).

Compared to the A62, the Starline A64 and A66 models have expanded functionality and smaller parts. Instead of a two-level shock sensor, they are equipped with a tilt sensor with position fixation on three axes, which signals when the car is lifted with a jack or moved on a tow truck. Also, A64 and A66 have a different design of key fobs, which are much smaller and lighter than those of A62.

The availability of a particular function, as well as the cost of alarms, can be found in the table:

• Price. The table shows the price of the basic set. Additional modules are purchased separately.
• CAN module. Allows you to integrate the alarm system into the car’s digital bus and ensures its more efficient operation.
• Control by phone. A GSM module with a mobile chip allows the driver to arm and disarm, enable auto-start and control the vehicle’s security using a special mobile application.
• Autostart. The engine is turned on remotely to warm it up and create a comfortable temperature in the cabin.
• Blocking using a relay. A wireless relay, which is installed anywhere in the body, prevents the engine from starting in the event of a theft.
• GPS module. Necessary in order to monitor the vehicle on-line. It is usually installed together with a GSM antenna.
• Communication control. In older models, you can check the connection by pressing the corresponding key on the remote control transmitter. In modern models, such a check is carried out automatically every 5-10 minutes. If the connection is lost, the system immediately notifies the owner.

User manual

According to the operating instructions, after installing the car alarm, you need to check the operation of the security mode. If the door locks lock and unlock when you turn the security on and off, you can begin setting up the system.

Setting up the key fob

Before using the pager, you must insert a working power source into the device. The battery is inserted into a special compartment located behind the back cover of the key fob.

To use all options, the communicator must be linked to the control unit:

1. When the ignition is turned off, the button to enter the emergency alarm maintenance mode is pressed 7 times.
2. The key in the lock is turned to the “ACC” position. When entering the key fob programming menu, the pager will emit 7 beeps.
3. On the remote control, press keys 1 and 2 simultaneously and hold for several seconds. You can release the buttons after one siren signal is heard. If linked, an icon in the form of an open lock will appear on the pager screen. These steps are repeated for each key fob being programmed. No more than 5 seconds should pass between pairing devices, otherwise the alarm will exit the programming menu.
4. To complete the setup process, the ignition in the car is turned off. The lights should flash three times.

Identification of buttons

Description of controls on communicators:

Correspondence of keys on Starline A62 remote controls

Table: key fob functions

LCD key fob display

The LCD display of the key fob is shown in the photo:

Designation of icons on the communicator screen

Description of indicators on the screen of the Starline A62 pager:

1. Communication quality icon when sending commands to the control unit.
2. An additional channel for controlling the tailgate is included.
3. Activation of additional channel number 1.
4. Indicator for checking the status of the anti-theft system.
5. Icon for activating and disabling the service maintenance mode.
6. Disabling the zone sensitivity controller.
7. Silent car security mode.
8. Vehicle protection with silent confirmation signals.
9. Car security with loud confirmation pulses.
10. Indicator of the enabled “Search” option for a car in the parking lot.
11. Panic mode is enabled.
12. Activation of a second additional channel for equipment control.
13. Anti-robbery mode is enabled.
14. Battery charge indicator in the remote control. If the icon blinks, the battery needs to be replaced.
15. Symbol of a running car engine.
16. Indicator of a call from the car owner from the passenger compartment.
17. The trunk or any door in the car is open.
18. A display with the current time, displaying the alarm status, as well as warnings about the sensitivity controller being triggered.
19. The warning or alarm zone of the shock sensor is turned on.
20. The alarm is activated.
21. Silent vehicle protection mode.
22. The car door locks are either locked or unlocked.
23. Indicator of siren operation in security mode. If the icon is crossed out, then silent protection is enabled.

Cursor-based alarm control

Configuring the anti-theft system options using the cursor method is done as follows:

1. The fourth button on the main communicator is pressed two or more times. This will begin the process of moving the cursor on the device display. The direction of its movement changes automatically when you double-click or pause.
2. Using the fourth control element, the cursor must be moved to the position of the required indicator.
3. To activate the selected function, briefly press the third key of the key fob, to disable it - the second. The setup menu is automatically exited after two seconds if the user does not press any buttons during this time.

Setting up autorun

Starline A62 alarm systems do not have an automatic engine start function. But its implementation is possible after installing an additional module. To do this, you can use Starline devices (for example, M31) or other analogues. Depending on the model, control is usually carried out through calls or SMS messages. The module, receiving a command with a certain code, performs the function remotely.

Emergency alarm shutdown

If the communicator from Starline A62 is lost or damaged, the security mode can be disabled using the service button:

1. The driver's door is opened with a key. This will trigger the siren alarms.
2. The key is inserted into the lock and turned to turn on the ignition. After activation, the button to enter emergency service mode is pressed several times. The number of “clicks” must correspond to the first digit of the personal code.
3. The ignition in the car is turned off. If a unique password is programmed, the security mode should be disabled. In confirmation, the car's external lights will blink twice. If the code is two-digit, then similar steps are repeated to enter the next character.

Factory reset

To reset all parameters to factory values, perform the following steps:

1. The car's ignition is turned off.
2. The emergency service mode entry button is pressed 9 times.
3. The key is turned in the lock to turn on the ignition. To confirm entering the reset menu, the siren will sound nine times.
4. Then the service mode key is pressed one more time. One siren signal will indicate that the settings have been reset.

Key Features

Features specific to the Starline A62 alarm system:

1. The presence of eight security zones operating independently from each other.
2. Possibility of activating the protection mode both using the communicator and using the Valet service key.
3. Passive blocking mode of the power unit.
4. Availability of a personal password. The PIN code can be used to unlock the system, activate the security mode and control basic functions.
5. Anti-hijack or anti-robbery option. The function is intelligent and is designed to prevent car theft in the event of a violent seizure of the car. The driver, after his car has been selected, can activate the function. After some time (usually 1 minute, but the interval can be programmed) after activation, the engine is blocked. The time interval is necessary so that the attacker can drive the car away from the car owner to a safe distance.
6. The presence of a warning zone, as well as the ability to completely deactivate the sensitivity controller when the protection mode is turned on.
7. Option for separate opening of door locks.
8. Function of bypassing non-working security zones. If, when the protection mode is activated, the alarm has performed diagnostics and detected non-working zones, they will be automatically disabled.
9. Availability of a memory unit built into the electronic module. It stores information about car alarm alarms with identification of the affected zone. Also, the presence of memory allows you to remember the alarm status. If the battery is disconnected, then after turning it on again, the alarm will return to the state in which it was before this event.
10. Using an anti-theft installation, the consumer can implement two locks of the power unit. This will provide additional engine protection. The signaling itself has a built-in universal lock. To turn it on, the consumer does not need to use additional relays. There is also one external blocking of the internal combustion engine.
11. Availability of an input for connecting an additional sensitivity controller.
12. Availability of an output for connecting a silent alarm signal. Information about alarm activation will be sent to the user's communicator. Instead of an alarm signal, lights may simply go off.
13. Presence of panic mode. Activating it will scare strangers away from the car. When the mode is turned on, alarm signals will start working, and the light alarm will also be activated.
14. The ability to automatically close or open door locks when the internal combustion engine is running or switched off.

The Starline A62 alarm system does not have the security option with the engine running.

Separately, the service capabilities of the signaling should be highlighted:

1. The presence of two additional channels, with which you can implement various service functions.
2. To control the central locking of the car, a special power relay is used, designed for a current of up to 10 amperes.
3. Possibility of implementing the Comfort function. Enabling it will ensure automatic closing of the electric sunroof, as well as the windows, when the protection mode is activated.
4. There is an option to delay the light signal after closing the door locks. The delay can be set to 5, 35 or 60 seconds.
5. Option to search for a car in the parking lot. If the driver forgets where he left the car, he can turn on this function. As a result, the alarm lights will begin to blink, which will allow you to find the car.
6. Silent activation of the protection mode.
7. Availability of an automatic signaling algorithm.
8. The consumer has the opportunity to choose the duration of the signals sent to the central locking.
9. Option to call the car owner from the salon. To do this, use the button located on the transceiver module.

Video: possible reasons for incorrect operation of the Starline alarm system

The “ReviewBroz34” channel in its video showed what problem a consumer may encounter when using Starline car alarms.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (66.67%)

No (33.33%)

X

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 3 votes, average: 4.67 out of 5)

Discuss the article:

Video - Installing StarLine A62 on Peugeot 308

For the next test, the Starline company presented two models of Starline alarm systems, A62 and B62 series. As a matter of principle, I asked not to bring models with automatic start, because... The “autorun” function does not add anything serious in terms of protection to the overall picture, but is only a service function. All the conclusions described below in no way serve as a guide to the selection of specific products, but only reflect the subjective assessment of the author.

Starline A62

What immediately catches your eye is the absence of an antenna. (it is hidden inside the case). The bodies of both key fobs are made of simple, fairly thick plastic with a minimum number of elements, which creates confidence in reliability. The top cover is attached quite firmly without the use of screws, the battery can be changed without difficulty.

The information display is informative, but in my opinion it is oversaturated with status icons. When requesting the status, it became possible to see not only the interior temperature, but also the battery voltage.

We open the lid and the first thing that caught our eye was the support phone number. We're calling. A minute of waiting, they picked up the phone and answered my questions correctly. It turned out that technical support works from 10-00 to 19-00. I'm calling at 18.55... They picked up the phone and answered. The key fob is bulky and large, but the ergonomics of use are excellent, the buttons are pressed easily and conveniently. The strength of the key fob was tested together with our friends - the company Ugona.net

Three key fobs of the A62 series fell under gravity onto the tiled floor, starting from a height of 1 meter and up to a height of 2.2 meters in increments of 0.2 meters. At each height, the fall occurred three times: the LCD display, the antenna and the buttons. Those. each keychain fell 21 times. All three key fobs remained in full working order, which was a pleasant surprise.

— high reliability of the key fob body; — availability of technical support telephone; — high impact resistance; — no external antenna; — ergonomics of keystrokes;

The installation was done efficiently, no traces of active production components were found. The connectors are securely attached to the board; reasonable efforts to try to tear the wires out of the connector socket ended in vain.

Anti-theft function

The entire anti-theft function boils down to an attempt to notify the car owner about the start of theft by sending an alarm message to the key fob, or to inform the owner about the loss of communication with the car using the “communication control” function if the thief jammed the alarm messages. To make theft more difficult, the engine blocking relay is built into the alarm unit, or the external blocking relay can be controlled by an analog output.

Therefore, if the alarm unit itself is detected in the cabin, disabling the blocking will not be difficult. A cracking light indication control relay, which remains electromechanical and has a characteristic sound (crackling) during pulse operation, will help the thief find the unit in the car when alarmed.

The A series unit has two additional channels controlled by a command from the remote control, which allows, if desired, control of devices such as Webasto, door pins, trunk lock, etc.

— high-quality installation of the block; — high-quality mounting harnesses; — the presence of two additional universal programmable channels.

— analog control of the blocking relay (no digital relays included) — crackling relay control indication, allowing you to find the alarm unit.

Starline B62

The body is made of higher quality plastic, the antenna is also hidden inside. The key fob fits well in the hand, the ergonomics of key pressing are excellent. Separately, I would like to note the excellent engineering solution to make a contrasting large arming button. It is easy to press by touch, and if such a remote control falls into the hands of a child, he will not be able to do anything other than arm the car.

Three key fobs of the StarLine B62 series turned out to be less resistant when dropped, stopping one after another when dropped from a height of 1.6 meters. The failure was accompanied by cracks in the LCD display matrix.

The pros and cons are absolutely similar to the A series, but the B series already has 4 additional channels, this allows you to control several devices at once.

Alarms of the StarLine A62 and B62 series are minimally resistant to theft and cannot be considered as a means of protection against theft. However, they can be confidently used as part of any security complex, assigning them a number of functions:

• remote control of arming/disarming mode;

• reliable notification of the owner about the start of theft or loss of communication with the car;

• the proposed interactive exchange mode with increased noise immunity makes it impossible for the factory code grabber 803 to operate;

• expanded ability to control external devices.

Please note that we do not install alarm systems. You can purchase StarLine alarms and install them in Moscow from our colleagues at the StarLine installation center.

Owner reviews

I drive a VAZ 2107. I chose the alarm based on price, as well as the presence of additional qualities. I don’t think that VAZs are being stolen from anyone now, so the main emphasis was on the convenience of the alarm. The choice fell on Starline B9, which, in addition to security functions (very good, by the way), can also boast additional autostart options and a decent price. The alarm has been on the car for a year now – no glitches and working properly, so I’m happy.

I’ll say right away - I bought it at the price of Starline B9. As for me, 4 thousand for a budget alarm system, but with good options, is quite good. It was recommended by a neighbor in the garage who uses it all the time, and especially praised the turbo timer, so I took it. It won't hurt me on diesel either. So far, the system has been working properly for six months, although I was a little afraid that I had screwed it up, because I installed it myself, and for me this was my first experience. But no complaints. The only drawback is poor sensitivity to the signal from the key fob. Already from the balcony of the 9th floor the car is not reachable, which is inconvenient. But the rest is all good.

A proven security system with a built-in Kan interface, auto-start, personal encryption keys, Dialog authorization and a built-in smart start function. The alarm is made taking into account the extreme factors of urban wave disturbances. Specialized in mid-level and business class cars.

How to set up auto start on Starline alarms

The dialogue encryption method, reliably protected from the reading devices of vehicle thieves, is the main feature and advantage of the Starline alarm system.
However, the alarm system, which is popular among domestic motorists, has a number of additional functions. In particular, auto start, all the delights of which can be fully appreciated in the harsh winter. Let's figure out how to enable autostart on the Starline alarm system from a key fob - remote control (RC), as well as using a special application for smartphones. Let's find out why autorun doesn't work. Let us shed light on other issues directly related to this topic. Fact. All models of the Starline security system are equipped with a self-diagnosis function. If any element of the system fails, the car owner will receive a corresponding notification on the key fob.

Autorun programming

Automatic engine start by timer

Also, the Starline B9 alarm system has the ability to autostart at certain time intervals. To set this parameter you need to:

• turn off the ignition, press the Valet key six times;
• turn the key, make sure there is sound and light confirmation;
• press the Valet button three more times;
• Now, by clicking on the remote control button, you can set the desired time after which the engine will start on its own. The first button is 2 hours, the second is 3 hours, the third is 4 hours, the first is long - once every 24 hours;
• confirmation and memorization are also automatic.

• You need to successively press keys 3 and 1 to move the cursor to the fan icon. Afterwards, a melodic signal from the remote control will sound;
• To enable this mode, you now need to press the second key.

Start on alarm

In Starline B9 systems, you can configure automatic start on an alarm clock. You should first make sure that the time on the key fob is set correctly in order for the program to run correctly.

You need to position the cursor on the corresponding clock icon (using the third button). Then you need to press the first button and hear a melodic signal. The time on the key fob should blink, and the car's dimensions should blink once.

Now the corresponding icon is displayed on the remote control, and the system has begun the countdown to autostart. The alarm clock indicators themselves are set in the same place as the clock parameter.

• You need to successively press keys 3 and 1 to move the cursor to the clock icon. Afterwards, a melodic signal from the remote control will sound;
• To turn off this mode, you now need to press the second key.

Setting autostart based on temperature

To automatically start based on temperature, this operation is carried out as follows:

• turn the ignition key to the OFF position, press the Valet service key 6 times;
• turn on the ignition, listen to 6 sound and light signals from the car, confirming entry into the programming mode;
• press the Valet button four more times;
• Now on the key fob we press the buttons corresponding to the required value (1st key = -5 degrees, 2nd = -10 degrees, 3rd = -18 degrees, long press of the first button = -25 degrees);
• confirmation of the received command is the corresponding number of sound or light signals (from 1 to 4). Memorizing this function will be automatic; you just need to not press anything for five seconds.

Temperature-based autostart can also be activated from the key fob - you need to use buttons 3 and 1, move the cursor to the thermometer icon and activate this option. As confirmation, one beep from the key fob will sound and the headlights will flash several times.

Below is a video with instructions on how to program your car to autostart based on engine or interior temperature.

How to disable engine auto start

You can control the engine start automatically using the Starline B9 key fob. You need to press the first key on the key fob for a long time, and then press the third button once. In one cycle, the car can make four attempts to start the engine. In case of failure, the message SP will be displayed on the remote control screen.

You can also remotely extend the operation of an already running engine. The key combination here is similar - press the first button for a long time, and then press the third key briefly. If you need to remotely stop the engine, you need to press the second button on the key fob for a long time, and then briefly click the third again.

Operating instructions for the StarLine A62 CAN alarm system and how to enable autostart

This car security system provides a full range of security and service functions, as well as interactive authorization.
Thus, an interactive control code with personal keys 128 bits long is capable of eliminating intelligent electronic hacking and is resistant to all available code grabbers. In order to protect the code, the most advanced dialog coding algorithm is used today, as well as the innovative frequency hopping method. In this method, when transmitting commands, a specialized transceiver changes frequencies many times according to a special program at the time of each transmission. A solution of this level, also known under the technical term: “method of possible spectrum expansion with frequency hopping,” is used for the first time in a car alarm control system and is a significant complication of attempts to crack the existing code.