Lada Largus - replacing lamps in the rear light

2283-15-14-07

By pressing the lamp and turning it counterclockwise, remove the combined brake signal and side light lamp from the holder.
By pressing the lamp and turning it counterclockwise, remove the combined brake signal and side light lamp from the holder.

By pressing the lamp and turning it counterclockwise, remove the combined brake signal and side light lamp from the holder.

We install the new P21/5W lamp in the reverse order. The protrusions on the base of the combined brake signal and side light lamp are located at different levels and during installation must fit into the corresponding grooves in the holder socket.

Standard replacement procedure

Replacing the low beam lamp, as well as the high beam, begins by disconnecting the on-board power supply. This precedes all electrical repair work. In this case, a special switch is turned or the negative terminal is disconnected from the battery, which avoids accidental short circuits or erroneous connections during installation.
The place where the Largus lamp will be replaced is determined. There, the rubber plugs covering the electrical components are removed, and two metal antennae are opened in front of the car owner, fixing them in the reflector. They are separated so that the used parts can come out of their seat without damaging the housing.
Next, you need to disconnect the plugs from the wiring that was previously disconnected. Here it is worth paying attention to the order of arrangement, otherwise, during the installation of new parts, everything can be mixed up and they will have to be changed again.
After connecting the plug with wiring to the new parts, they are mounted in place and secured with antennae. You should try not to touch the flasks with your hands, as this can lead to their rapid failure.
If the light is dim during lighting, and the headlights flash when you turn on the headlights, then it is imperative to restore the contacts of the wires with the vehicle body. This is especially true for a marker lamp, because the fat that gets there begins to evaporate when heated and can cause ignition.
At the end of this procedure, you need to put on the rubber plugs and secure all the parts in their places. After this, the car will be ready for use and the driver does not have to worry about malfunctions of the Lada Largus lighting fixtures.

As practice shows, in modern domestic cars, one of which is the Lada Largus, lamps with directional luminous flux are most often used. The essence of such lighting is a reliable view in front of and behind the car. At the same time, inconvenience to other traffic participants heading towards the driver or driving behind is excluded.

2283-15-14-08

Similarly, we replace the turn signal lamp (PY21W) and the fog light lamp (P21W) (reverse lamp in the right lamp).
Similarly, we replace the turn signal lamp (PY21W) and the fog light lamp (P21W) (reverse lamp in the right lamp).

Similarly, we replace the turn signal lamp (PY21W) and the fog light lamp (P21W) (reverse lamp in the right lamp).

Removing Largus taillights - search on DRIVE2

Brighter, brighter reverse (replacing bulbs and adding a light).

1. We do it from the back

PTF
reversing
2. We install lamps of higher brightness. I don't like cars with different lights at the back. That is, on one piece of glass there is a white window for ZH, and on the other there is a red window for PTF.

Removing scuffs above the rear lights - Lada Largus.

Largus has it

Another small problem that I fixed today.
The black trims above the rear
lights have three bumps with which they rest on the body and rub off the paint. The result is this or even worse when it is rubbed down to the metal.

Improved reverse gear without losing the rear PTF - Lada Largus.

Hi everybody! Today I’ll tell you about a modification to the rear

travel and
rear
PTF.
Everyone knows that Largus
only has one
reversing
, and it is located in the right
rear
light.

Repair of rear accessory 2nd generation flashlight - Lada Largus.

Review from the owner of Lada Largus

— electronics.

Lada Largus

2015, petrol engine 1.6 l., 105 l. p., front drive, manual transmission — electronics.

Installation of rear additional lights. — Lada Largus.

the rear ones were purchased

add. the lights sat in the garage for another month until I found the time to install them. I bought them at a car market in my city, took the first generation lights, there were also second generation ones available, but I didn’t like them.

Minus the rear fog light, plus the reversing light.

Review from the owner of Lada Largus

Diodes in reverse. — Lada Largus, 1.6 l., 2015

Review from the owner of Lada Largus

— electronics. hi all. As soon as the agent returned home after the repair, he immediately began to receive good money.

How to shoot

I won’t paint lanterns, everyone knows that, but it’s cold outside and I wanted to put them up quickly. We took it apart and compared the lamps.

Correct connection of the tow bar and rear accessories.

Finally it turned out to be a relatively warm day, I had some free time and I decided to connect the electrics to the previously installed additional rear

lights and tow bar (www.drive2.ru/l/524122075749680777/).

Second reversing light! — Lada Largus, 1.6 l., 2014.

Review from the owner of Lada Largus

— tuning.
I always didn’t like this Euro standard with one reverse
!

2283-15-14-09

The turn signal lamp has two protrusions, located asymmetrically relative to the axis of the lamp, which must fit into the corresponding grooves in the holder socket.
The turn signal lamp has two protrusions, located asymmetrically relative to the axis of the lamp, which must fit into the corresponding grooves in the holder socket.

The turn signal lamp has two protrusions, located asymmetrically relative to the axis of the lamp, which must fit into the corresponding grooves in the holder socket.

Some technical characteristics and general description

In order not to buy a pig in a poke, having decided to stylishly tune your car, it is advisable to familiarize yourself with the proposed description of the technical characteristics of the product. What material is the additional lighting made of, how long will it last, and how justified is such a purchase? Let's figure it out together. A meager description on the packaging is one thing, and an objective view from the outside is another.

Let’s say right away that such lights shine really well on Largus. It is also noteworthy that this illumination is practically indistinguishable from the illumination of the main lights and is, in fact, its logical continuation. This will definitely emphasize the individuality of your car and will be a simple, but at the same time effective visual tuning.

When it comes to light source technology, LED lighting is currently the most technologically advanced. It is capable of providing high-quality light for tens of thousands of hours and for at least ten years. Such lamps are also not afraid of low temperatures, are economical and shock-resistant. They do not heat up the lamp body like outdated halogen samples. In general, it’s a pleasure.

The red impact-resistant ABS plastic of the lampshade also looks very presentable and reliable, which adds overall points in favor of purchasing the product. After installation, the lights will hardly stand out in any way. The product looks natural and harmonious, as if the lamps were installed there from the very beginning.

The price of such “pleasure” is approximately 3 thousand rubles. It largely depends on the region of the country and the dealer offer of a particular store. You can hardly find a simpler and cheaper tuning of your car. Therefore, from this point of view, this acquisition also seems very attractive. The only thing that upsets us is the cost of installing the lamps at service centers.

Why is it profitable to install additional rear tuning lights on the Lada Largus yourself?

Official service centers estimate the cost of what we are about to tell you at about 3 thousand rubles (the price of the work is commensurate with the cost of the product). The most generous offer from a service center that we saw on the Internet was only 1,500 rubles. It’s unlikely that anyone will want to tinker with your car for less money except you. You can install additional taillights on your Lada Largus yourself, spending about an hour on everything and saving a decent amount of money.

The manufacturer even kindly includes instructions, once again explaining how these lamps are installed correctly. You will hardly need the above-mentioned manual, because you will get all the necessary information from our article. By understanding the algorithm of actions in advance, you can avoid a lot of unpleasant moments of inept and blind tuning.

2283-15-14-10

Each lamp holder socket is marked with the type of lamp.
Each lamp holder socket is marked with the type of lamp.

Each lamp holder socket is marked with the type of lamp.

Install the rear light in the reverse order.

[How to save on maintenance of Lada Largus] [Maintenance of Lada Largus at 15,000/45,000/75,000/105,000 km] [Maintenance of Lada Largus at 30 thousand km] [Maintenance of Lada Largus at 60 thousand km of run] [Maintenance of Lada Largus for 90 thousand km of run] [Maintenance of Lada Largus for 120 thousand km of run] [Independent maintenance - general recommendations] [Safety rules for self-carrying out maintenance] [Tools required for carrying out maintenance Lada Largus maintenance] [Lamps used in the Lada Largus car]

Changing the lamps in the rear light of Lada Largus

Rear additional tuning lights for Lada Largus

Since its appearance, Lada Largus has acquired enviable popularity among Russian car enthusiasts seeking not only comfort, but also practicality. This station wagon is adapted to the realities of domestic roads and is a clone of the popular Romanian car Dacia Logan MCV, produced since 2006.

Lada Largus (RF-90) went on sale in 2012 and is currently available in three variations:

universal passenger car LADA Largus with five seats;
high-capacity option with seven seats in the cabin;
means for transporting goods.

For this LADA Largus car, you can select and install additional rear lights. These devices make it possible to better identify the vehicle on the road surface, and also give the station wagon a more presentable appearance. The plug for the mounting socket of this optics is painted black and does not improve the overall picture of the exterior from the stern. Many Lada Largus owners agree on this opinion. This circumstance encourages most owners to get rid of these overlays by installing additional lighting devices instead. The most popular product option is the use of LED devices. Before installing additional rear lights, you will need to remove the specified plugs. Upon completion of installation, the devices are connected to the on-board network according to the attached instructions.

Installation instructions

To remove the plug and install additional rear lights instead, perform the work in the following sequence:

Remove the main light from the rear of the body. To do this, you will need to unscrew 2 fasteners and then disconnect the block.
After the lamp is removed, remove the upholstery inside the car, located on the rear pillars.
Remove 3 fasteners holding the trim on the outside, and 1 fastener on the inside of the car. Remove the cover itself. If you have a 7-seater Lada Largus station wagon, you will need to remove the window fasteners, pistons, and mounting bolts for seat belts.
Remove the pin from the trim. It will need to be screwed into a similar place in the trim on the additional lamp.
Attach additional optics to the place of the lining using nuts.
After connecting the wiring and checking the operation of the additional lighting, put the main optics in their original place.

Additional rear lights for Lada Largus
To connect the Lada Largus optics according to the diagram, you will need:

PTF from reflectors.

The next day I removed the rear bumper reflectors. Carefully cut the diffuser from the base with a construction knife. We glue sealed LED strips (I used SMD 5050), two in each reflector, 9 pcs. in each segment.

It turned out to be two rows of 18 LEDs, the third row did not fit. Having drilled holes in the base of the reflectors, I ran the wires through there and soldered the tape to the finished two-pin connector so that it could be removed if anything happened. I sealed everything, and for tightness and reliability I soldered the edges with a soldering iron, it’s still not visible.

Left reflector.

I ran the wires from the right reflector to the left along the rear bumper and further up the bumper to the left lamp. The ground wire for the reflectors (I had a green one, there was no black one) was connected to the headlight ground (black wire), and the power wire (mine was purple) was connected to the pink PTF power wire left over from last time. We don’t look at the numbering of contacts in the diagram, it doesn’t quite match.

Instructions on how to dismantle plugs on Largus

To dismantle the plugs and subsequently install additional lighting devices instead of the plugs, we proceed according to the following algorithm.

We remove the standard stern lights. For this purpose, unscrew a couple of screws and disconnect the connectors.
Now we remove the upholstery from the internal panels of the body pillars of the Lada Largus trunk.
We remove three fastening components holding each pad on the outside, and the same fastening clamp from the inside.
We remove the pads. In the 7-seater version, you will additionally need to remove the window fastening elements, pistons and bolts securing the seat belt holders.
Next, we remove the studs from the plugs, which after installing the optics will need to be screwed into identical mounting sockets.
We install the lighting fixtures in place of the plugs and secure them with nuts.
After connecting to the network, we check the functionality of the devices.
After making sure that everything works, you can begin installing the standard optics.

To connect additional Largus optics according to the attached diagram you will need:

Disconnect the terminals from the battery.
Connect the wiring of new devices to the section of the cable network that provides power to the main optics.
The wires in these lighting devices are marked in different colors, where: the yellow cable is responsible for the side lighting, the black cable is ground, and the red cable provides the functionality of the braking mode signal.
The cable network of pre-installed optics is marked as yellow, black and blue cables. They respectively provide connection: brake signal, ground and dimensions.
We insulate the connection areas of the cable ends.
Before checking the operation of the installed devices, we connect the battery.
Turn on the side lights and press the brake pedal.

This is how you can make tuning on your car and instead of plugs, install additional rear lights, which are decorative in nature.