Standard fog lights (PTF) on the Lada are only available in the “Lux” trim levels. If you are the owner of a car with a simpler configuration (“Norma” or “Standard”), then you can install PTF on a sedan, station wagon, hatchback or liftback yourself according to the simplest and most universal scheme..
Preparatory stage (selection of PTF for Lada Granta)
The range of PTFs is not large; it is represented by several domestically produced models. Some owners claim that PTFs from Opel and Ford are compatible, but the information has not been verified.
| Name / manufacturer / article | Price, rub.) |
| LADA Granta (VAZ 2190) / Kalina 2 / LADA Largus OSRAM Kit 21900-3743010 | from 2800 |
| Kit 21900-3743011 | —/— |
| —/— 2190-3743011 | —/— |
| —/— 2190-3743010 | —/— |
| PTF wiring kit for LADA Granta (2190 2874498) | from 600 |
| PTF "LUCH" set 1118-3743010/11 | from 1800 |
| PTF glass (02B08507) Granta / Kalina 2 / Largus, Datsun | from 750 |
| AUTOMOTIVE LIGHTING / BOSCH (982469641) | from 2000 |
*prices are as of September 22, 2018.
Procedure for self-installation of fog lights on a Lada Granta liftback
We place the car on a flat platform with access around the perimeter.
- We dismantle the front bumper along with the radiator grille.
- Using a milling cutter, we cut holes in the openings for the PTF.
- We install the fog lights and secure them to the fasteners.
- We connect the blocks with wires.
- Reinstall the bumper. We check the functionality of the system.
Step-by-step process for preparing and installing fog lights
In the auto store we purchase: PTF, corrugation (at least 3.0 m), adapters - adapters for PTF with standard wiring.
- To remove the front bumper, unscrew three self-tapping screws on each side, four plastic clips, three “10” bolts in the lower perimeter;
- We remove the structure along with the radiator grille;
It is important to know!!! In the Norma and Standard models, there is no hole for adjusting the fog lights. The owners independently cut out a diameter of “8”. In the Liftback body modification, the opening is factory-made.
- We cut out the opening for the fog lights along the contour, it is factory-made;
- To make it smooth, treat the surface with a household hairdryer;
- We fix the headlights on three standard mounts;
- We connect adapters to each of the lamps, since the standard block with wires is short, its length is not enough;
- We put on the front bumper, screw it in with bolts and plastic clips.
Installation of PTF
The entire installation process is divided into two stages according to complexity:
- Direct preparation of seats and securing PTFs in them;
- Integration of electrical components into the standard wiring system.
Seating equipment
To carry out this operation you must:
- Remove the front bumper;
- Cut holes;
- Provide reliable fixation of lighting fixtures.
Advice! If the fog lights of the Lada Grant vibrate on uneven roads, they will blind oncoming drivers. Therefore, take care about their secure fixation. Also order the production of stickers for the headlights - this will help protect them from damage.
The bumper from the Granta must be removed
After dismantling the bumper, you need to install it on a flat surface. Then arm yourself with a sharp needle file and start cutting out holes.
Do the work slowly - this way you will avoid breakdowns
As a result of this work, the edges of the holes will be uneven.
But it's not a problem:
- Take a small diameter sanding stone;
- Clamp it into a drill or cordless impact wrench;
- Carefully trim the edges of the holes.
Be careful when working with plastic
The housings must now be installed into the prepared holes.
To do this, turn the bumper over and:
- Insert PTF;
- We combine the mounting holes with the fastening points;
- We fix them using self-tapping screws;
- We inspect from the front side the correct installation;
- If everything is in order, use a screwdriver to tighten the screws until they stop.
The photo shows the process of fixing PTF
Connection to electrical circuit
The instructions included in the installation kit prescribe the following connection procedure:
- Insert incandescent lamps;
- Fix the pads on the plinth;
Fully assembled PTF
- Pull the wires from the headlights through the engine compartment into the car interior;
- Install the relay and fuse into the mounting block;
It is important to securely fasten the wiring
- Connect one of the wires to the rear PTF power button;
- Install the bumper on the car;
- Connect the battery and check that the fog lights are working correctly. (see also the article VAZ wiring: the need for modernization)
The control button will combine the operation of the PTF
Wiring diagram for fog lights Lada Granta liftback
Engine compartment
- We lay an additional wire from the right PTF headlight to the left one. We solder it and bring it into the engine compartment to connect to the relay.
- We fix the mass to the body at the place where the bumper is attached, maybe under the license plate, in the center.
- Do not forget to lay all electrical wiring in a corrugated material made of fireproof material.
Interior of the Lada Granta liftback car
- We lay the corrugated hose through the hole in the hydraulic corrector seal.
- The connection is best made at the ignition switch. That is, when turned off, the headlights will go out automatically.
- Open the glove box lid, press the side stops, and remove the lid.
- We stretch our hand into the cavity and carefully squeeze out the block of two buttons for controlling the heated glass and PTF.
- We power the minus from the heater button. Plus we won’t take it, since they will be activated at the same time.
- We connect the positive cable and install the unit again.
- We connect to the positive from the ignition switch unit (blue wire), it is located under the steering wheel.
- Finally, we power the relay - regulator: ground - wire from the button - end to the PTF - plus to the ignition.
In each specific configuration, the color scheme of the wire may differ. Read the diagram in the instruction manual for details. Classic colors: red, yellow, blue, brown. If you do not want to supply power through the ignition switch, the connection diagram is simplified with one less procedure.
Connection
Below is a universal diagram for connecting a PTF using an additional button. The PTF kit contains everything necessary for installation and connection. In some cases, it may be necessary to lengthen the wires (cross-section of at least 0.75 sq. mm), be prepared for this.
It is recommended to hide the wiring under the hood in corrugation (cambric). We route the wires from the engine compartment to the passenger compartment through standard holes in the engine panel (the hole above the pedals). It is most convenient to place the relay inside the panel, behind the light control module (LCM). Plus, for switching the PTF, we take it from the battery or in the mounting block (most often this is a thick pink wire). Other useful contacts can be found in the table from the article on installing an alarm system. We install the button in any place convenient for you.
From the factory, the PTF is controlled via the light control module, diagram:
In our case, a separate, new button will be used to turn on the fog lights. The advantage of such a universal PTF connection is that the installation process is very simple and does not require much time and money. The disadvantage is that there is no indication of the fog lights on the dashboard, but this can all be solved by modifying the panel.
The process of installing and connecting the PTF on the Lada Granta FL is shown in the video:
By the way, do you know what is needed to convert a regular Lada Granta into a new FL?
Keywords: fog lights Lada Granta | fog lights Lada Kalina | fog lights Lada Priora | bumper Lada Granta | bumper Lada Kalina | bumper Lada Priora | external lighting for Lada Granta | external lighting for Lada Kalina | external lighting for Lada Priora | headlights of Lada Granta | headlights of Lada Priora | headlights Lada Kalina
+8
Share on social networks:
Found an error? Select it and press Ctrl+Enter..
Step-by-step instructions for installing a rear fog light
Many Lada Granta Liftback car owners are surprised to hear about this, but it is a fact. Of course, we are not talking about PTF in its classic form, but about a laser brake light. It is installed in the rear of the car and informs the driver behind about the vehicle. Since there is no strictly defined installation location, it is customary to fix it in the area of the license plate, under the lower contour of the bumper, in the spoiler. There are known cases of embedding an accessory inside.
A bright red light beam informs drivers behind, preventing accidents. The brake light is also used when it is necessary to notify the driver of the need to switch the high beam headlights. An alternative way to use lighting when backing up or parking in conditions of limited visibility. The maximum effective beam length is 25.0 meters. Exceeding the length does not guarantee the quality of lighting.
The voltage is supplied from the left/right brake light. Activation is possible either by pressing the brake pedal or by a separate button. The owner makes the decision based on personal beliefs. In practice, activation occurs with an autonomous button, since when driving backwards it is not always advisable to use the standard brake pedal. It is strictly forbidden to point the laser beam at the windshield area behind the driving driver.
Reviews
| № | Positive |
| 1. | Kirill , 36 years old: after purchasing a Lada Grant from the showroom, I immediately purchased a PTF from OSRAM 21900-3743010. I didn’t install it at the service station because I can do it myself. In general, I am satisfied with the quality of lighting, no complaints. |
| 2. | Vitaly , 29 years old: it is obvious that there are not enough foglights out of the box. I often drive at night and need a good view of the road. Since I don’t understand manufacturers, I entrusted it to a specialist at a service station. PTF Lada Granta liftback - my advice. |
| 3. | Georgiy , 37 years old: I’ve been working as a taxi driver for the second year, my shift often ends after one in the morning. The disadvantage of the standard lighting system is obvious. I bought a “LUCH” set 1118-3743010/11 at the market. The cost is 1850 rubles, the quality is good, installation couldn’t be simpler. |
| 4. | Victor , 25 years old: I work as an entrepreneur, purchasing goods from hundreds of kilometers away. By morning the products should be on the counter. To help the standard headlights, I installed PTF. Second week, no complaints. |
| 5. | Maxim , 28 years old: I leave my positive review of BOSCH fog lights (982469641). Special thanks to the store manager for his practical advice. |
| 6. | Konstantin , 37 years old: during scheduled maintenance, he ordered the service of installing a PTF from a technician. I chose OSRAM 21900-3743010 because the price and quality are at a decent level. Numerous positive reviews. |
| 7. | Vladimir , 48 years old: I was a little upset by the lack of fog lights from the box on the Lada Granta liftback. I had to install it myself last weekend. The lighting is good, no complaints. |
| Negative | |
| 1. | Alexander , 36 years old: not only are fog lights not included in the kit, but they also provide poor lighting. We are talking about a domestic manufacturer. Installed by BOSCH (982469641). I use it myself and recommend it to others. |
| 2. | Vitaly , 39 years old: installed domestic PTF OSRAM 21900-3743010. I regretted buying it, wasted money. The quality is below average, the angle of inclination is several degrees. I don't recommend it. |
| 3. | Vyacheslav , 37 years old: not happy with the installed fog lights, they don’t cover the side of the road, visibility is mediocre, the light is dim. |
Conclusion Every product has its own buyer. If you don’t find fault with a budget car, which is the Lada Granta Liftback, the quality of PTF lighting is good, it is enough for visibility. Of course, when compared with headlights from foreign brands in the premium segment, the advantage of the latter is obvious. In order to increase the service life of accessories, purchase products exclusively from certified points of sale. Require the provision of documents, check the functionality on site.
Video “Detailed instructions for installing optics”
Detailed instructions for installing fog optics in a garage with a description of all the nuances and features are given in the video below (the author of the video is the NapoziTiV channel).
Fog lights are a useful option for every car owner. In addition to working directly during fog, they can also be used in normal night modes to increase the fan of light in front of the car. However, on the Lada Granta, as on many modern cars of this class, fog lights (hereinafter referred to as PTF) are not installed on all trim levels. Today we will look at installing them ourselves.
